Manufacturing · Precision engineeringWest Midlands, United Kingdom

A £1.15m capacity investment with little room for delay

A proposed £1.15m machining cell had little headroom in its operating model. The equipment order became binding before the required customer contracts were secured, and first-year output fell below the base assumption.

Key figures

Capital budget
Approximately £1.15m
Assumed annual capacity
4,200 productive hours
Reported first-year output
Approximately 3,640 hours
Subsequent contracted annual volume
Approximately 4,100 hours

Sequence of events

  1. August 2023Conditional board approval; equipment order became binding.
  2. September 2023Required contracts secured, bringing contracted annual volume to approximately 4,100 hours.
  3. November 2023Cell commissioned.
  4. December 2023 – November 2024Reported output of approximately 3,640 hours.

The challenge

A privately owned precision-engineering subcontractor in the West Midlands was considering a 5-axis machining cell with pallet automation. Customers were requesting work that its existing 3-axis and 4-axis machines could not perform in-house to the required specification. Some work was subcontracted; other opportunities had been declined.

Members of the Gambit Reign team undertook the advisory work while working at a previous consultancy. Their remit covered demand assessment, capacity analysis, scenario modelling, investment appraisal and proposed approval conditions. The client led equipment selection, negotiations and implementation. The client and former consultancy remain confidential.

This account reflects recollections of the engagement. Historical figures and financial inputs are approximate; the calculations below show what the stated assumptions imply. Advisory work took place in 2023, with operating results reported to 30 November 2024.

Separating capability from demand

The existing shop was around 80% utilised. That did not establish whether sufficient profitable work existed for the new capability. The appraisal needed to connect identifiable customer work with achievable prices, productive hours and additional costs.

The £627,000 associated with subcontracted work represented payments to suppliers. It was not customer revenue. Dividing that cost by a £285 hourly selling rate does not establish 2,200 hours of demand. A 3,900-hour annual scenario illustrates the model’s economics, but the purchase-ledger figure does not substantiate those demand hours.

Letters of intent and sales opportunities also required scrutiny of qualification, timing, cancellation rights and price. Customer interest alone did not guarantee deliverable, profitable production.

The operating model had limited headroom

The approximate £1.15m budget comprised £650,000 for the machining centre, £220,000 for pallet automation, £95,000 for tooling and fixtures, £125,000 for installation and site works, and £60,000 contingency.

The illustrative model assumed 4,200 productive hours a year, revenue of £285 per hour, variable costs of £165.30 per hour and contribution of £119.70 per hour, or 42%. It included a £270,000 annual fixed-cost allowance.

The return calculations use a £1.15m initial outflow and eight annual year-end inflows, with modelled EBITDA used as a cash-flow proxy. They exclude tax, financing, working-capital movements, further capital spending and disposal proceeds.

At 3,900 hours a year, this model gives an eight-year IRR of approximately 7.6%, below the stated 10% hurdle. At 4,200 hours it gives approximately 12.2%. Meeting 10% requires about 4,057 whole productive hours. A 4,100-hour run-rate leaves only about 43 hours above that threshold.

These are standalone scenarios. A complete incremental appraisal must distinguish additional cash costs from overhead allocations and account for earnings retained by continuing to subcontract. The quoted 8% subcontract margin and 42% in-house contribution cannot be compared without a consistent revenue and cost basis; the available figures do not quantify that adjustment.

The condition was not met before commitment

The board gave conditional approval in August 2023, requiring sufficient contracted volume before capital was committed. The equipment order became binding that August. The required contracts were secured in September, bringing contracted annual volume to approximately 4,100 hours.

The pre-commitment condition was therefore not met. Later contracts improved the demand position, but they could not retrospectively provide the safeguard intended before the order became binding. The cell was commissioned in November 2023.

First-year output and the subsequent outlook

Reported output for December 2023 to November 2024 was approximately 3,640 hours, or 86.7% of assumed annual capacity. This was 260 hours below the 3,900-hour base assumption and 460 hours below the later contracted run-rate.

A customer qualification delay was reported as contributing to the slower ramp-up. Applying the model’s prices and costs to first-year hours gives approximately £1.04m revenue and £166,000 EBITDA; these are model-based estimates, not a separately verified cash-flow statement.

The subsequent Year 2 contracted run-rate was approximately 4,100 hours. At unchanged model inputs, that implies about £1.17m revenue and £221,000 annual EBITDA. Repeating that stronger run-rate for all eight years gives approximately 10.7% IRR. Keeping the lower first year and assuming seven years at the Year 2 run-rate gives approximately 9.5%. Both are projections under the stated conventions, not realised investment returns.

What the decision teaches

A capacity decision needs evidence for the specific capability being purchased, a like-for-like comparison with the alternative, and a realistic ramp-up plan. Supplier expenditure cannot substitute for customer revenue or job-level hours.

Conditional approval also depends on sequencing. A requirement intended to protect a capital commitment must be satisfied before that commitment becomes binding. Subsequent commercial progress does not erase the timing gap or the effect of a weaker first year on whole-project returns.

Discuss your capacity investment appraisal

Gambit Reign supports manufacturers with demand assessment, capacity analysis and investment appraisal.

Related service: Project Feasibility & Commercial Appraisal