Deferring a £2m production line through operational improvement
A food manufacturer considering a second production line used a focused improvement programme to release capacity from its existing operation and defer the larger investment.
Key figures
- Reported OEE improvement
- 61.9% → 66.4%
- Indicative additional annual capacity
- ~3,600 tonnes
- Programme cost
- ~£362,000
- Proposed production line deferred
- £2m
Figures are approximate. The capacity figure is an OEE-based equivalent at unchanged operating hours and product mix, not a separately verified measure of additional sales.
Introduction
A privately owned food manufacturer in North West England was considering a £2m second production line to meet growing demand. Before committing, it reviewed how effectively its existing line was being used.
Members of the team now at Gambit Reign undertook this engagement in their previous consultancy roles. Working with the client’s production managers and shift supervisors, they assessed production losses, designed an improvement programme and supported implementation. The client retained responsibility for delivery, operating decisions and resources.
Understanding the constraint
The existing line operated across two shifts, but downtime and changeovers were not being recorded consistently. The business needed a clearer view of the capacity it could recover before deciding whether a second line was necessary.
The review established structured measurement of overall equipment effectiveness, or OEE. The reported starting point was approximately 61.9%, with availability at 80%, performance at 85% and quality at 91%. Together, these measures showed where productive capacity was being lost through stops, reduced speed and defects.
The 38.1% gap to full effectiveness was a combined measure of these losses. It did not mean the line was stopped for 38.1% of its scheduled time. Availability losses accounted for approximately 20% of planned production time and became the main focus of the capacity work.
Designing the improvement programme
The programme combined four areas of work, supported by practical training and clearer shift-level reporting.
- Changeovers: separate preparation from tasks requiring a stopped line, pre-stage materials and standardise tooling and procedures.
- Maintenance: introduce operator-led daily routines, identify critical spares and address the main causes of unplanned downtime.
- Material yield: improve measurement, visual quality standards and shift-level reporting to make waste easier to identify and address.
- Energy: investigate and repair compressed-air leaks, assess motor-drive improvements and optimise refrigeration settings.
Production managers were equipped to deliver training internally so that the operating routines could continue beyond the advisory work. The programme included measurement equipment and motor-drive changes as well as training, systems and advisory support.
Implementation and reported results
Following an initial review of approximately six weeks, the board approved the operational programme in April 2023. Implementation ran over the following 12 months, led by the client with advisory support and performance reviews.
The reported first-year OEE measure was approximately 66.4%, an improvement of 4.5 percentage points. Availability rose to about 84.7%, performance to 85.2% and quality to 92.0%. Availability made the largest contribution to the overall improvement.
For the approximately 50,000-tonne annual reference output used in the case, the change from 61.9% to 66.4% equates to around 3,600 tonnes of additional annual capacity at unchanged operating hours and product mix. This describes the capacity implied by the OEE change; it should not be read as a separate claim that the same volume was produced and sold.
The client reported that the improvement provided sufficient capacity for its immediate demand and deferred the proposed £2m second line. Programme cost was approximately £362,000.
The improvement fell short of the initial ambition of around 68% OEE. Adoption of the maintenance routines was slower than planned, and the material-measurement equipment arrived about ten weeks late. These delays affected the pace at which benefits could be realised.
Reading the financial result
The reported management estimate was approximately £989,000 in gross annual benefits. Applying its 80% flow-through assumption gives approximately £792,000 before programme cost. Deducting the approximately £362,000 programme cost produces an estimated benefit after programme cost of approximately £430,000.
This is a modelled benefit calculation using management estimates that have not been independently verified. Its value depends on how recovered capacity converts into sales, how costs change and when the improvements take effect. Part of the reported energy reduction also came from milder weather, limiting the amount that can be attributed solely to the programme.
- Reported gross annual benefit estimate
- ~£989,000
- After the stated 80% flow-through assumption
- ~£792,000
- Programme cost
- ~£362,000
- Estimated benefit after programme cost
- ~£430,000
The decision was about timing and scale
The programme addressed the immediate demand gap with a smaller upfront commitment. Its approximately £362,000 cost was about 18% of the proposed £2m capital project. The options offered different amounts of capacity and different operating requirements, so that ratio alone does not establish which would be the better long-term investment.
The value of the work was to give the board a measured basis for deferring the larger project while improving the existing operation. A future expansion decision would still need to consider sustained demand, the remaining recoverable losses, operating costs, resilience and the practical limits of the line.
What other manufacturers can take from this
Before approving a capacity expansion, establish where the current constraint sits and measure the losses around it. Quantify the capacity that can realistically be recovered, then test its commercial value against the cost and timing of an additional line.
There is no universal OEE threshold that makes expansion right or wrong. Product mix, process constraints, changeovers and the reliability of the underlying measurements all matter. Operational improvement is most useful when the analysis is connected to a practical delivery plan and the demand the business actually needs to serve.
Discuss your operational improvement assessment
Gambit Reign supports manufacturers with resource baselines, loss analysis and operational improvement programmes.
